Difference between revisions of "Baofeng UV-82 Disassembly"
From Bloominglabs
(Created, added sections and pictures.) |
(Add to category) |
||
| (One intermediate revision by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[File:1_whole_radio.jpg|Baofeng UV-82]] | + | [[File:1_whole_radio.jpg|200px|Baofeng UV-82]] |
Because I could not find any instructions on the internet, here are instructions on how to disassemble the Baofeng UV-82 handheld transceiver. | Because I could not find any instructions on the internet, here are instructions on how to disassemble the Baofeng UV-82 handheld transceiver. | ||
==Remove Belt Clip== | ==Remove Belt Clip== | ||
| − | [[File:2_remove_belt_clip.jpg|2 small philps screws]] | + | [[File:2_remove_belt_clip.jpg|500px|2 small philps screws]] |
==Unclip Battery== | ==Unclip Battery== | ||
| − | [[File:3_unclip_battery.jpg]] | + | [[File:3_unclip_battery.jpg|500px]] |
| − | [[File:4_remove_battery.jpg]] | + | [[File:4_remove_battery.jpg|500px]] |
==Remove Antenna and Volume Knob== | ==Remove Antenna and Volume Knob== | ||
| − | [[File:5_unscrew_antenna.jpg]] | + | [[File:5_unscrew_antenna.jpg|500px]] |
| − | [[File:6_remove_volume_knob.jpg|It just pulls straight off.]] | + | [[File:6_remove_volume_knob.jpg|500px|It just pulls straight off.]] |
| − | == | + | ==Unscrew Retaining Rings== |
| − | [[File:7_remove_antenna_retainer.jpg]] | + | [[File:7_remove_antenna_retainer.jpg|500px]] |
| − | [[File:8_remove_volume_retainer.jpg]] | + | [[File:8_remove_volume_retainer.jpg|500px]] |
==Pry Open Case== | ==Pry Open Case== | ||
| − | [[File:9_unpry_bottom_clips.jpg]] | + | [[File:9_unpry_bottom_clips.jpg|500px]] |
| − | [[File:10_bottom_popped_out.jpg]] | + | [[File:10_bottom_popped_out.jpg|500px]] |
==Remove Rear Case and Circuit Board== | ==Remove Rear Case and Circuit Board== | ||
| − | [[File:11_remove_back.jpg]] | + | [[File:11_remove_back.jpg|500px]] |
==Remove Rubber Pieces== | ==Remove Rubber Pieces== | ||
| − | [[File:12_rubber_jack_seal.jpg]] | + | [[File:12_rubber_jack_seal.jpg|500px]] |
| − | [[File:13_keypad.jpg]] | + | [[File:13_keypad.jpg|500px]] |
==Disassembled== | ==Disassembled== | ||
| − | [[File:14_disassembled.jpg]] | + | [[File:14_disassembled.jpg|500px]] |
| + | |||
| + | [[Category:Guides]] | ||
Latest revision as of 10:15, 5 December 2017
Because I could not find any instructions on the internet, here are instructions on how to disassemble the Baofeng UV-82 handheld transceiver.
Contents |
[edit] Remove Belt Clip
[edit] Unclip Battery
[edit] Remove Antenna and Volume Knob
[edit] Unscrew Retaining Rings
[edit] Pry Open Case
[edit] Remove Rear Case and Circuit Board
[edit] Remove Rubber Pieces
[edit] Disassembled
